Orange County NC Website
Browse       Search
Orange County Health Department Improvements Smith Sinnett /2024008 <br />Hillsborough,NC Orange County Asset Management Services <br />WIRING DEVICES 26 27 26 - 2 <br />1.06 DELIVERY,STORAGE,AND PROTECTION <br />A Store in a clean,dry space in original manufacturer's packaging until ready for installation. <br />PART 2 PRODUCTS <br />2.01 WIRING DEVICE APPLICATIONS <br />A Provide wiring devices suitable for intended use and with ratings adequate for load served. <br />B For single receptacles installed on an individual branch circuit,provide receptacle with ampere rating not <br />less than that of the branch circuit. <br />C Provide weather resistant GFCI receptacles with specified weatherproof covers for receptacles installed <br />outdoors or in damp or wet locations. <br />D Provide GFCI protection for receptacles installed within 6 feet of sinks. <br />E Unless noted otherwise,do not use combination switch/receptacle devices. <br />2.02 WIRING DEVICE FINISHES <br />A Provide wiring device finishes as described below unless otherwise indicated. <br />B Wiring Devices,Unless Otherwise Indicated: ​White​with​​​stainless steel​wall plate. <br />C Wiring Devices Installed ​in Finished Spaces​: ​White​with​​​stainless steel​wall plate. <br />D Wiring Devices Installed ​in Unfinished Spaces​: ​White​with​​​galvanized steel​wall plate. <br />2.03 WALL SWITCHES <br />A Manufacturers: <br />1.Hubbell Incorporated​​: www.hubbell.com/#sle. <br />2.Leviton Manufacturing Company,Inc​​. <br />3.Pass &Seymour,a brand of Legrand North America,Inc​​ <br />4.​Approved Equal​. <br />B Wall Switches -General Requirements: AC only,quiet operating,general-use snap switches with silver <br />alloy contacts,complying with NEMA WD 1 and NEMA WD 6,and listed as complying with UL 20​​;types <br />as indicated​on the drawings​. <br />1.Wiring Provisions: Terminal screws for side wiring and screw actuated binding clamp for back wiring <br />with separate ground terminal screw. <br />C Standard Wall Switches:​Industrial heavy duty grade​,​20​A,​120/277​V with ​standard toggle type​switch <br />actuator and maintained contacts;​single pole single throw,three way,or four way​as indicated​on the <br />drawings​. <br />2.04 WALL DIMMERS <br />A Manufacturers: <br />1.Leviton Manufacturing Company,Inc​​. <br />2.Lutron Electronics Company,Inc​​. <br />3.Pass &Seymour,a brand of Legrand North America,Inc​​ <br />4.​Or approved equal​. <br />B Wall Dimmers -General Requirements: Solid-state with continuous full-range even control following <br />square law dimming curve,integral radio frequency interference filtering,power failure preset memory,air <br />gap switch accessible without removing wall plate,complying with NEMA WD 1 and NEMA WD 6,and <br />listed as complying with UL 1472;types and ratings suitable for load controlled as indicated on the <br />drawings. <br />C Provide accessory wall switches to match dimmer appearance when installed adjacent to each other. <br />D Contractor shall ensure dimmer switch compatibility with luminaire controlled prior to ordering. <br />2.05 RECEPTACLES <br />A Manufacturers: <br />1.Hubbell Incorporated​​: www.hubbell.com/#sle. <br />2.Leviton Manufacturing Company,Inc​​. <br />3.Pass &Seymour,a brand of Legrand North America,Inc​​. <br />4.​Approved equal​. <br />Docusign Envelope ID: 2D852F9B-A7CF-462A-9536-444A53AA848A