Orange County NC Website
Browse       Search
Orange County Health Department Improvements Smith Sinnett / 2024008 <br />Hillsborough, NC Orange County Asset Management Services <br />INTERIOR ARCHITECTURAL WOODWORK 06 40 23 - 2 <br />1. Lumber with or for transparent finish, not less than 50 sq. in., for each species and cut, finished on <br />1 side and 1 edge. <br />2. Lumber and panel products with shop-applied opaque finish, 50 sq. in. for lumber and 8 by 10 inches <br />for panels, for each finish system and color, with 1/2 of exposed surface finished. <br />3. Plastic laminates, 8 by 10 inches, for each type, color, pattern, and surface finish, with 1 sample <br />applied to core material and specified edge material applied to 1 edge. <br />4. Thermoset decorative-panels, 8 by 10 inches, for each type, color, pattern, and surface finish, with <br />edge banding on 1 edge. <br />5. Solid-surfacing materials, 6 inches square. <br />6. Exposed cabinet hardware and accessories, one unit for each type and finish. <br />F. Product Certificates: For each type of product, signed by product manufacturer. <br />G. Qualification Data: For Installer and fabricator. <br />1.5 QUALITY ASSURANCE <br />A. Fabricator Qualifications: Shop that employs skilled workers who custom-fabricate products similar to <br />those required for this Project and whose products have a record of successful in-service <br />performance. Work shall meet or exceed AWS standards. <br />B. Installer Qualifications: Work shall meet or exceed AWS standards. <br />C. Quality Standard: Unless otherwise indicated, comply with WI’s "Manual of Millwork" for grades of <br />interior architectural woodwork indicated for construction, finishes, installation, and other requirements. <br />D. Fire-Test-Response Characteristics: Where fire-retardant materials or products are indicated, provide <br />materials and products with specified fire-test-response characteristics as determined by testing identical <br />products per test method indicated by UL, ITS, or another testing and inspecting agency acceptable to <br />authorities having jurisdiction. Identify with appropriate markings of applicable testing and inspecting <br />agency in the form of separable paper label or, where required by authorities having jurisdiction, imprint <br />on surfaces of materials that will be concealed from view after installation. <br />1. Surface-Burning Characteristics: Not exceeding values indicated below, tested per ASTM E 84 for <br />standard time period (10 minutes). <br />a. Flame Spread: 75. <br />b. Smoke Developed: 450. <br />E. Preinstallation Conference: Conduct conference at Project site to comply with requirements in Division 01 <br />Section "Project Management and Coordination." <br />1.6 DELIVERY, STORAGE, AND HANDLING <br />A. Do not deliver woodwork until painting and similar operations that could damage woodwork have been <br />completed in installation areas. If woodwork must be stored in other than installation areas, store only in <br />areas where environmental conditions comply with requirements specified in "Project Conditions" Article. <br />1.7 PROJECT CONDITIONS <br />A. Environmental Limitations: Do not deliver or install woodwork until building is enclosed, wet work is <br />complete, and HVAC system is operating and maintaining temperature and relative humidity at occupancy <br />levels during the remainder of the construction period. <br />B. Field Measurements: Where woodwork is indicated to fit to other construction, verify dimensions of other <br />construction by field measurements before fabrication, and indicate measurements on Shop Drawings. <br />Coordinate fabrication schedule with construction progress to avoid delaying the Work. <br />1. Locate concealed framing, blocking, and reinforcements that support woodwork by field <br />measurements before being enclosed, and indicate measurements on Shop Drawings. <br />2. Established Dimensions: Where field measurements cannot be made without delaying the Work, <br />establish dimensions and proceed with fabricating woodwork without field measurements. Provide <br />Docusign Envelope ID: 186E0FF8-664C-4A5C-9F97-28196CE69FD1