2019-521-E AMS - Otis Elevator Whitted repair

Browse Search

05/20/2019_CLC version © OTIS ELEVATOR COMPANY, 2015 All Rights Reserved Page 10 of 16 10. SMOKE & HEAT SYSTEM - Provide a smoke and heat detector system, located as required with wiring from the sensing devices to each elevator controller. 11. SPRINKLERS - Provide code compliant sprinkler system, as required, in the hoistway, pit and machine room. 12. AIR CONDITIONING - Provide suitable ventilation and cooling equipment, if required, to maintain the machine- room temperature between 45oF and 95oF. The relative humidity should not exceed 85 percent non- condensing. 13. CUTTING & PATCHING - Do any cutting, (including cutouts to accommodate hall signal fixtures, entrances and/or machine room access, machine beams, belt drop for Gen2 machines) patching, reinforcing and painting of walls, floors or partitions. 14. MACHINE ROOM ACCESS - Provide a self-locking and self-closing door for the elevator machine room. Access door to be adequately sized to accept our equipment. Modify machine room access, as required, to comply with code and facilitate safe entrance and egress of all equipment. 15. FIRE EXTINGUISHER - Provide ABC fire extinguisher in elevator machine room. 16. BARRICADES – Otis to furnish standard folding barricades only. If required, you are to provide, maintain and remove any temporary barricades per OSHA or local authority requirements and furnish barricades to protect the public from access to construction areas. Furnish and maintain infection control separation as required. 17. NON-ELEVATOR MATERIAL IN HOISTWAY - Remove or encapsulate, as required, any non-elevator related pipes or wiring located in the elevator machine room or hoistway. 18. HOISTWAY LEDGES - Provide per ASME code, a 75-degree angle constructed of a non-combustible material on all ledges that are 4” are greater in the hoistway, excluding multi-hatch divider beams. 19. HOISTWAY VENTILATION - Provide code compliant hoistway ventilation. Local Code Authority may require a means to prevent the accumulation of hot air and gasses at the top of the hoistway. Pressurizing the hoistways, or providing vents from the top of the hoistway to the outside of the building usually accomplishes this. Vents shall not be less than 3 1/2% of the area of the hoistway nor less than 3 sq. ft. for each elevator car, whichever is greater. You may not vent the hoistway to the machine room. If the hoistway vents must run through the machine room, they must be enclosed in a fire rated structure and not violate clearances around our equipment. 20. SUMP HOLE GRATING - Provide a flush grating over the sump hole located in the elevator pit. 21. PROJECT BEING “DRIED-IN”- Work, as required, to keep the elevator lobbies, hoistway, machine room and storage area “dried-in” for the entire length of the project. 22. ASBESTOS – Should any asbestos be found to be present in the building or elevator equipment which is related to any of our work, it shall be the responsibility of others to abate, contain, dispose or prepare the workplace as safe for our employees to work within or about. Otis will not be responsible for working with asbestos which may be disturbed or uncontained. Otis will not be responsible for any costs associated with delay of the job should asbestos be detected or require addressing by others for us to proceed. This includes but is not limited to re-mobilization charges which may be applied. 23. STORAGE - Provide dry, protected and secure storage space adjacent to or within 100’ rollable access to the hoistway(s). Otis shall be compensated for material delivered that is stolen or removed from the jobsite. If remote storage or “conex” box storage is required, it shall be provided at an extra cost. 24. DISPOSAL - The disposal of removed elevator components; machines, controllers, ropes, hydraulic fluid, oils, buffers and packing materials from the new equipment and any and all related materials shall be the sole responsibility of the Owner. If a dumpster is provided on site, we will deposit waste materials in the dumpster or at an agreed upon on-site location for removal by the owner. Owner shall properly dispose of oils, liquids and hazardous materials. DocuSign Envelope ID: 47D12065-7220-4277-A47F-FC1DAC0CA54F