|
DocuSign Envelope ID: B94F2D40-3B3C-47A7-86C2-6F1 B4F92C62C
<br /> -ELSAMRI I RRRCJAWSTAN
<br /> 2. Rollers: Use rollers of carpet, velvet back, or high-pile sheep's wool as recommended by the manufacturer
<br /> for the material and texture required.
<br /> 3. Spray Equipment: Use airless spray equipment with orifice size as recommended by the manufacturer for the
<br /> material and texture required.
<br /> D. Minimum Coating Thickness: Apply paint materials no thinner than manufacturer's recommended spreading rate.
<br /> Provide the total dry film thickness of the entire system as recommended by the manufacturer.
<br /> E. Mechanical and Electrical Work: Painting of mechanical and electrical work is limited to items exposed in equipment
<br /> rooms and in occupied spaces.
<br /> F. Mechanical items to be painted include, but are not limited to,the following:
<br /> 1. Piping, pipe hangers, and supports.
<br /> a. Paint exposed gas piping Safety Yellow.
<br /> 2. Heat exchangers.
<br /> 3. Tanks.
<br /> 4. Ductwork.
<br /> 5. Insulation.
<br /> 6. Motors and mechanical equipment.
<br /> 7. Accessory items.
<br /> G. Electrical items to be painted include, but are not limited to,the following:
<br /> 1. Conduit and fittings.
<br /> 2. Switchgear.
<br /> 3. Panelboards.
<br /> H. Block Fillers:Apply block fillers to concrete masonry block at a rate to ensure complete coverage with pores filled.
<br /> I. Prime Coats: Before applying finish coats, apply a prime coat of material, as recommended by the manufacturer, to
<br /> material that is required to be painted or finished and that has not been prime coated by others. Recoat primed and
<br /> sealed surfaces where evidence of suction spots or unsealed areas in first coat appears,to ensure a finish coat with
<br /> no burn through or other defects due to insufficient sealing.
<br /> J. Pigmented (Opaque) Finishes: Completely cover surfaces as necessary to provide a smooth, opaque surface of
<br /> uniform finish, color, appearance, and coverage. Cloudiness, spotting, holidays, laps, brush marks, runs, sags,
<br /> ropiness, or other surface imperfections will not be acceptable.
<br /> K. Stipple Enamel Finish: Roll and redistribute paint to an even and fine texture. Leave no evidence of rolling, such as
<br /> laps, irregularity in texture, skid marks, or other surface imperfections.
<br /> L. Completed Work: Match approved samples for color, texture, and coverage. Remove, refinish, or repaint work not
<br /> complying with requirements.
<br /> M. Rated Walls: Create stencil and paint wall rating above ceiling at 20'-0" max o.c. and at all wall directional changes.
<br /> Coordinate text requirements with the requirements of the local building official.
<br /> -FF L/ EAMMN
<br /> A. Cleanup: At the end of each workday, remove empty cans, rags, rubbish, and other discarded paint materials from
<br /> the site.
<br /> 1. After completing painting, clean glass and paint-spattered surfaces. Remove spattered paint by washing and
<br /> scraping. Be careful not to scratch or damage adjacent finished surfaces.
<br /> -R J DOSELSUM
<br /> A. Protect work of other trades, whether being painted or not, against damage by painting. Correct damage by
<br /> cleaning, repairing or replacing, and repainting, as approved by Architect.
<br /> B. Provide "Wet Paint" signs to protect newly painted finishes. Remove temporary protective wrappings provided by
<br /> others to protect their work after completing painting operations.
<br /> 1. At completion of construction activities of other trades, touch up and restore damaged or defaced painted
<br /> surfaces. Comply with procedures specified in PDCA P1.
<br /> -FS EXSEDAD JAMS-LHEO#/ E
<br /> A. General: Provide the following paint systems for the various substrates, as indicated.
<br /> B. Zinc-Coated Metal with Semi-Gloss Direct to Metal ("DTM") Acrylic Enamel Finish: 2 topcoats of DTM semi-gloss
<br /> enamel over acrylic bonding primer,with min.total DFT of 2.5 mils.
<br /> 1. Prime Coat (Tie-Coat): Lead-free, acrylic base interior/exterior galvanized metal primer, premium grade.
<br /> Apply over(universal)shop primer.
<br /> a. PPG: 90-712 Series, Pitt-Tech DTM Primer/Finish.
<br /> ©BOOGEDAMN 0E-NM792-1 RI I RRR56 19RGeadowlands Drive,Hillsborough,ML
<br /> ODAMNE LO#MS8, ML 93UU2
<br />
|