Orange County NC Website
Browse       Search
DocuSign Envelope ID: B94F2D40-3B3C-47A7-86C2-6F1 B4F92C62C <br /> —ELSIDMRI I RRRCJAIMSIMN <br /> 1. Protect from freezing. Keep storage area neat and orderly. Remove oily rags and waste daily. Take <br /> necessary measures to ensure that workers and work areas are protected from fire and health hazards <br /> resulting from handling, mixing, and application. <br /> 9R' JDOVELSLOMOISIDM- <br /> A. Apply water-based paints only when the temperature of surfaces to be painted and surrounding air temperatures <br /> are between 50 and 90 deg F. <br /> B. Do not apply paint in snow, rain, fog, or mist; or when the relative humidity exceeds 85 percent; or at temperatures <br /> less than 5 deg F above the dew point; or to damp or wet surfaces. <br /> 1. Painting may continue during inclement weather if surfaces and areas to be painted are enclosed and heated <br /> within temperature limits specified by manufacturer during application and drying periods. <br /> 9F1 EXSDA GASEDIA/- <br /> A. Furnish extra paint materials from the same production run as the materials applied in the quantities described <br /> below. Package paint materials in unopened, factory-sealed containers for storage and identify with labels <br /> describing contents. Deliver extra materials to the Owner. <br /> 1. Quantity: Furnish the Owner with extra paint materials in the quantities indicated below: <br /> a. Interior, Low-Luster Acrylic Finish: One case of each color applied. <br /> b. Interior, Semi-Gloss Acrylic Enamel: 2 gal. of each color applied. <br /> 2. Quantity: Furnish the Owner with an additional 5 percent, but not less than 1 gal. or 1 case, as appropriate, <br /> of each material and color applied. <br /> J ADS 3 5J DOO#L S- <br /> WS GAM#. ALS#DED- <br /> A. Products: Subject to compliance with requirements, provide one of the products in the paint schedules. <br /> B. Manufacturers Names: The following manufacturers are referred to in the paint schedules by use of shortened <br /> versions of their names,which are shown in parentheses: <br /> 1. Benjamin Moore&Co. (Moore). <br /> 2. Sherwin-Williams Co. (S-W). <br /> 3. PPG Industries(PPG). <br /> 4. Rosco Laboratories(RL)for repainting the existing stage-Alternate 1. <br /> 3F3 JA7VIS GASEDZA/-, NEMEDA/ <br /> A. Material Compatibility: Provide block fillers, primers, undercoats, and finish-coat materials that are compatible with <br /> one another and the substrates indicated under conditions of service and application, as demonstrated by <br /> manufacturer based on testing and field experience. <br /> B. Material Quality: Provide manufacturer's best-quality paint material of the various coating types specified. Paint- <br /> material containers not displaying manufacturer's product identification will not be acceptable. <br /> 1. Proprietary Names: Use of manufacturer's proprietary product names to designate colors or materials is not <br /> intended to imply that products named are required to be used to the exclusion of equivalent products of <br /> other manufacturers. Furnish manufacturer's material data and certificates of performance for proposed <br /> substitutions. <br /> C. Colors: Match colors indicated by reference to manufacturer's color designations. <br /> D. Green Seal Requirements: All paints used must meet GreenSeal requirements for VOC and chemical component <br /> limits,which are as follows: <br /> 1. The VOC concentrations (in grams per liter) of the product shall not exceed those liter below as determined <br /> by the US Environmental Protection Agency(EPA) Reference Test Method 24. The calculation of VOC shall <br /> exclude water and tinting color added at the point of sale. <br /> a. Interior Coatings; Non Flat: 150 g/l. <br /> b. Interior Coatings; Flat: 50 g/I. <br /> c. Exterior Coatings; Non Flat: 200 g/I. <br /> d. Exterior Coatings; Flat: 100 g/I. <br /> e. All Anti-Corrosive Coatings: 250 g/I. <br /> 2. Chemical Component Limitations-Aromatic Compounds: The product must contain no more than 0.5% by <br /> weight of the sum total of aromatic compounds. Testing for the concentration of these compounds will be <br /> performed if they are determined to be present in the product during a materials audit. <br /> 3. Chemical Component Limitations-Other Chemicals: The manufacturer shall demonstrate that the following <br /> chemical compounds are not used as ingredients in the manufacturer of the product: <br /> a. 1,2-dichlorobenzene. <br /> ©BOOGEDAMN 0E—NM792-1 RI I RRR5- 19RGeadowlands Drive,Hillsborough,ML <br /> ODAMN E L O#MS8, MIL 931Y192 <br />