Orange County NC Website
Browse       Search
DocuSign Envelope ID: B94F2D40-3B3C-47A7-86C2-6F1 B4F92C62C <br /> —ELSAMRI I RRRCJAMSIMN <br /> 5. Full gloss refers to high-sheen finish with a gloss range more than 65 when measured at a 60-degree meter. <br /> 9P -#BGISSA/- <br /> A. Samples for Verification: Of each color and material to be applied, with texture to simulate actual conditions, on <br /> representative Samples of the actual substrate. <br /> 1. Provide stepped Samples, defining each separate coat, including block fillers and primers. Use <br /> representative colors when preparing Samples for review. Resubmit until required sheen, color, and texture <br /> are achieved. <br /> 2. Provide a list of materials and applications for each coat of each sample. Label each sample for location and <br /> application. <br /> B. Product Data: Submit manufacturer's technical information including paint label analysis and application <br /> instructions for each material proposed. Include paint system schedule in the format used in this specification <br /> section. Include Material Safety Data Sheet for each paint product use. Include VOC content in grams per liter. <br /> 1. Manufacturing Location: Cut sheets or letter from manufacturer stating the location of material manufacturer, <br /> and the location of the mining or harvest of raw materials. <br /> 2. Material Cost: Statement of material cost(not including labor and equipment). <br /> C. Provide manufacturer's certificates that indicate that paint complies with low VOC limits specified. <br /> 9FF 4#A/IS8 A--#DAML E <br /> A. Applicator Qualifications: Engage an experienced applicator who has completed painting system applications <br /> similar in material and extent to that indicated for this Project with a record of successful in-service performance. <br /> B. Source Limitations: Obtain block fillers, primers, and undercoat materials for each coating system from the same <br /> manufacturer as the finish coats. <br /> C. Benchmark Samples (Mockups): Provide a full-coat benchmark finish sample of each type of coating and substrate <br /> required on the Project. Comply with procedures specified in PDCA P5. Duplicate finish of approved prepared <br /> samples. <br /> 1. The Architect will select one room or surface to represent surfaces and conditions for each type of coating <br /> and substrate to be painted. <br /> a. Wall Surfaces: Provide samples on at least 100 sq.ft. of wall surface. <br /> 2. After permanent lighting and other environmental services have been activated, apply coatings in this room <br /> or to each surface according to the Schedule or as specified. Provide required sheen, color, and texture on <br /> each surface. <br /> a. After finishes are accepted, the Architect will use the room or surface to evaluate coating systems of a <br /> similar nature. <br /> 3. Final approval of colors will be from job-applied samples. <br /> 4. Mockups on Existing, Previously Painted Surfaces: Perform surface prep required by Part 3 and/or the <br /> manufacturer's surface prep requirements,then provide finish sample mock-up of 100 sq.ft.for each coating <br /> type and surface condition. Do not proceed with work until mockups have been reviewed and accepted by <br /> Owner and Architect. If existing coating is incompatible with specified coating to be applied inform Architect <br /> prior to application.' <br /> 91131 JDOO#LS-JELTT- EMQDOMGEMSA/ DE4#IDEGEMS- <br /> A. Chemical Component Limitations-VOC: The manufacturer shall demonstrate that the paint does not exceed the <br /> VOC concentrations allowed by the EPA's"South Coast Air Quality Management District"VOC regulations. <br /> 9F6 0 E/IQED8,-SODANE,AND HAMO/IMN <br /> A. Deliver materials to the Project Site in manufacturer's original, unopened packages and containers bearing <br /> manufacturer's name and label, and the following information: <br /> 1. Product name or title of material. <br /> 2. Product description (generic classification or binder type). <br /> 3. Manufacturer's stock number and date of manufacture. <br /> 4. Contents by volume,for pigment and vehicle constituents. <br /> 5. Thinning instructions. <br /> 6. Application instructions. <br /> 7. Color name and number. <br /> 8. VOC content. <br /> B. Store materials not in use in tightly covered containers in a well-ventilated area at a minimum ambient temperature <br /> of 45 deg F. Maintain containers used in storage in a clean condition,free of foreign materials and residue. <br /> ©BOOGEDAMN 0E—NM792-1 RI I RRR53 19RGeadowlands Drive,Hillsborough,ML <br /> ODAMN E L O#MS8, ML 931Y192 <br />