Orange County NC Website
Browse       Search
DocuSign Envelope ID: B94F2D40-3B3C-47A7-86C2-6F1 B4F92C62C <br /> —ELSAMRI I RRRCJAMS7VIN <br /> J ADS 9 5N EMEDA/ <br /> 91119 -#GGAD8 <br /> A. This Section includes surface preparation and field painting of the following: <br /> 1. Exposed exterior items and surfaces. <br /> 2. Exposed interior items and surfaces. <br /> 3. Surface preparation, priming, and finish coats specified in this Section are in addition to shop priming and <br /> surface treatment specified in other Sections. <br /> 4. Surface repairs associated with existing walls in renovation projects. <br /> 5. Painting the existing wood stage floor per Alternate 1. <br /> B. Paint exposed surfaces, except where the paint schedules indicate that a surface or material is not to be painted or <br /> is to remain natural. If the paint schedules do not specifically mention an item or a surface, paint the item or surface <br /> the same as similar adjacent materials or surfaces whether or not schedules indicate colors. If the schedules do not <br /> indicate color or finish, the Architect will select from standard colors and finishes available. <br /> 1. Painting includes field painting of exposed bare and covered pipes and ducts (including color coding), <br /> hangers, exposed steel and iron work, and primed metal surfaces of mechanical and electrical equipment. <br /> 2. Do not paint any roof deck,floor deck or exposed structure. <br /> C. Do not paint prefinished items, concealed surfaces,finished metal surfaces, operating parts, and labels. <br /> 1. Prefinished items include the following factory-finished components: <br /> a. Architectural woodwork and casework. <br /> b. Flush wood doors that have factory finish. <br /> c. Metal toilet enclosures. <br /> d. Metal lockers. <br /> e. Finished mechanical and electrical equipment. <br /> f. Light fixtures. <br /> g. Distribution cabinets. <br /> 2. Concealed surfaces include walls or ceilings in the following generally inaccessible spaces: <br /> a. Foundation spaces. <br /> b. Furred areas. <br /> c. Ceiling plenums. <br /> d. Pipe spaces. <br /> e. Duct shafts. <br /> 3. Finished metal surfaces include the following: <br /> a. Anodized aluminum. <br /> b. Stainless steel. <br /> 4. Operating parts include moving parts of operating equipment and the following: <br /> a. Valve and damper operators. <br /> b. Linkages. <br /> c. Sensing devices. <br /> d. Motor and fan shafts. <br /> 5. Labels: Do not paint over Underwriters Laboratories (UL), Factory Mutual (FM), or other code-required labels <br /> or equipment name, identification, performance rating, or nomenclature plates. <br /> D. Related Sections include the following: <br /> 1. Division 05, Section"Structural Steel Framing"for shop priming structural steel. <br /> 2. Division 05, Section"Metal Fabrications"for shop priming ferrous metal. <br /> 3. Division 08, Section"Hollow Metal Doors and Frames"for shop priming steel doors and frames. <br /> 4. Division 09, Section"Gypsum Board Assemblies"for surface preparation for gypsum board. <br /> 9F3 0 E. M15UM- <br /> A. General: Standard coating terms defined in ASTM D 16 apply to this Section. <br /> 1. Flat refers to a lusterless or matte finish with a gloss range below 15 when measured at an 85-degree meter. <br /> 2. Eggshell refers to low-sheen finish with a gloss range between 5 and 20 when measured at a 60-degree <br /> meter. <br /> 3. Satin refers to low-sheen finish with a gloss range between 15 and 35 when measured at a 60-degree meter. <br /> 4. Semi-gloss refers to medium-sheen finish with a gloss range between 30 and 65 when measured at a 60- <br /> degree meter. <br /> ©BOOGEDAMN 0E—NM792-1 RI I RRR59 19RGeadowlands Drive,Hillsborough,ML <br /> ODAMNE LO#MS8, ML 93UU2 <br />