2017-276-E AMS - Roof Control Services of North Carolina, Inc. for waterproofing to stop water infiltration into DA Building

Browse Search

DocuSign Envelope ID:05BAC521-A573-4502-9361-CAFO7F6BEC40 TEST DATA the surface for at least 5 seconds before being absorbed. NCHRP#244(@200 ftz/gal) Coverage rates on horizontal concrete surfaces are typically Series II 86%reduction in water absorption between 150 and 250 ft2/gal.Coverage rates on vertical Series II 87%reduction in chloride absorption surfaces depend on the type of material to be treated.Your Series IV 99%reduction in chloride absorption Protectosil representative can give an exact coverage rate ASTM C 672"Deicer Scaling" for your particular project.Please refer to the"Protectosil 100 cycles-0+rating CHEM-TRETE 40 VOC Application Instructions"for more (non-air-entrained concrete) detailed information. ASTM E303"Skid Resistance" Precautions:Protectosil CHEM-TRETE 40 VOC is a Dry surface no change flammable liquid and should be kept away from heat,sparks, Wet surface no change open flame and other sources of ignition.Protectosil Alberta DOT Penetrating Sealers Type lb CHEM-TRETE 40 VOC containers should be kept closed Initial water repellency 84.3% when not in use and should be stored at temperatures After abrasion 85.1% between 0°F(-18°C)and 120°F(50°C),away from rain and standing water.When working in an enclosed area,an air ASTM E 514"Water Permeance of Masonry" respirator should be used.Please refer to the material safety Untreated leakage 5.51/hr(1.5 gal/hr) data sheet for more detailed information. Treated leakage 0.01/hr(0.0 gal/hr) Reduction in leakage 100% AVAILABILITY ASTM C67 Water Absorption of Brick Protectosil CHEM-TRETE 40 VOC is available in 24 hours 98%effective 5-gallon pails and 55-gallon drums. Shipped F.O.B. 5 days 91%effective throughout the United States and Canada. Contact your local ASTM D 1653 Water Vapor Transmission Protectosil representative or your regional manager for spe- 75.8 g/ft2/24 hours,100%breathable cific cost information.You can obtain their contact informa- tion on our website,www.protectosil.com,or by calling us at INSTALLATION 1(800)828-0919. Concrete must be allowed to cure for a minimum of 28 days. All repointing must be completed and allowed to cure for at TECHNICAL SERVICE least 3 days.Concrete repair and replacement must be Technical service engineers and scientists are available to completed prior to application of Protectosil CHEM- answer questions about product performance,application TRETE 40 VOC.Patching materials,caulking,sealing mate- methods and compatibility with other building materials. rials and traffic paint must be fully cured before applying You can speak to one of our engineers or scientists directly Protectosil CHEM-TRETE 40 VOC. by calling our toll-free number,1(800)828-0919,and se- All surfaces must be cleaned to remove all traces of dirt, lecting option 1. dust,efflorescence,mold,salt,grease,oil,asphalt,laitance, curing compounds,paint,coatings and other foreign materi- MANUFACTURER als.Acceptable surface cleaning methods include shotblast- Evonik Corporation ing,sandblasting,waterblasting,and using chemical clean- 299 Jefferson Road ers.Check with your Protectosil representative to verify that Parsippany,NJ 07054-0677 surface preparation is adequate. 1(800)828-0919 Protectosil CHEM-TRETE 40 VOC should be applied using info.protectosil�a evonik.com low-pressure(15 to 25 psi)pumping equipment with a wet www.protectosil.com fan type spray nozzle.Alternate methods include using PROTECTOSIL PRODUCTS ARE MANUFACTURED AF either a power roller with a 1"nap or a brush.Do not alter or THE EVONIK CORPORATION TH IEODORE,ALABAMA, dilute the material.Do not apply to a wet or damp substrate. A test patch should be applied to the substrate by a PLANT UNDER A QUALITY SYSTEM CERTIFIED TO ISO- Protectosil representative to verify coverage rate and 9001 AND ISO 14001 REQUIREMENTS. application conditions. On vertical surfaces,apply Protectosil CHEM-TRETE 40 VOC in a flooding application from the bottom up,so the material runs down 6 to 8 inches below the spray pattern. On horizontal surfaces,the liquid material should pond on For more information,MSDS and the most updated product information,and to find your local representative,go to www.protectosil.com Protectosil®,CHEM-TRETE®=registered trademarks of Evonik Industries This information and all technical and other advice are based on Evonik Corporation's("Evonik")present knowledge and experience.However,Evonik as- sumes no liability for such information or advice,including the extent to which such information or advice may relate to third party intellectual property rights.Evonik reserves the right to make any changes to information or advice at any time,without prior or subsequent notice.EVONIK DISCLAIMS ALL REPRESENTATIONS AND WARRANTIES,WHETHER EXPRESS OR IMPLIED,AND SHALL HAVE NO LIABILITY FOR MERCHANT ABILITY OF THE PRODUCT OR ITS FITNESS FOR A PARTICULAR PURPOSE(EVEN IF EVONIK IS AWARE OF SUCH PURPOSE),OR OTHERWISE.EVONIK SHALL NOT BE RESPONSIBLE FOR CONSEQUENTIAL,INDIRECT OR INCIDENTAL DAMAGES(INCLUDING LOSS OF PROFITS)OF ANY KIND.It is the customer's sole responsibility and obligation to arrange for inspection and testing of all products by qualified experts.Reference to trade names used by other companies is neither a recommendation nor an endorsement of the corresponding product,and does not imply that similar products could not be used.