Orange County NC Website
DocuSign Envelope ID:2E5F960A-00C2-416D-B3AC-552CB78379FF <br /> INSTALLATION: <br /> To ensure proper installation and compliance to building codes, it is recommended that a qualified <br /> person or carpenter perform the installation of the unit. The unit must be properly installed onto <br /> a permanent wall that is capable of supporting significant weight and can accommodate the <br /> supplied installation hardware. The Koala Baby Changing Station meets ADA regulations when <br /> properly installed. Installer should account for the space that a unit occupies when in the down <br /> position and with the caregiver(whether standing or seated) in front of the unit. Locate the unit so <br /> that paths of travel are maintained around it when being used. <br /> Drilling holes and mounting the station: <br /> 1. Remove changing station from the shipping container and check for any freight damage. <br /> If damage is found, please call Koala Kare Products' Customer Service at 888.733.3456. Remove <br /> "Installation Kit" and "Operator Kit" from box. Please give "Operator Kit" to facility manager or <br /> operator. Box should contain two pieces: the bed and metal mounting chassis and the wall mount <br /> liner dispenser. Identify the best location for installing the unit. <br /> 2. Standard Installation- Remove the bed and chassis from the box and select the wall <br /> area where the unit will be installed. Make sure you have taken into consideration the operating <br /> clearance of 91/2" (241 mm) on both sides of the exposed chassis and 23 3/16" (589 mm)from wall <br /> surface when open. Measure from the floor 421/4" (1073 mm) on stud center and mark the wall. <br /> The mounting holes are designed for 16" stud centers. Ensure the locations you have marked <br /> for the mounting holes are level before drilling. Drill pilot holes for keyhole mounting using a 1/8" <br /> regular drill bit. <br /> Masonry or Tile over Stud Wall- Use a 7/32" (6 mm) masonry drill bit for the pilot hole until you <br /> hit the stud. Change bit to 1/8" (3 mm) regular drill bit. <br /> Metal Stud or Concrete Block- If the wall has wood studs that are not on 16" (406 mm) <br /> centers, has metal studs or an underlying surface of concrete block, drill with a 1/2" (13 mm) <br /> masonry bit. (You may have to purchase toggles before installing.) You must allow a minimum of <br /> inside wall space for toggles to turn depending on toggles used. Insert and tighten toggles. <br /> 3. Screw two of the mounting screws into the pilot holes leaving 1/4" (6 mm) exposed to <br /> allow keyhole slots to be easily mounted over the screw heads. Place chassis over screws. After <br /> securing the unit using the keyhole slots, verify that the unit is level. Tighten top two screws so <br /> that they are flush with the wall. Use the four lower holes as a guide to mark and drill pilot holes. <br /> Use remaining four screws and four washers to complete installation of bed and metal mounting <br /> bracket. Insert washers over lower four screws. All SIX screws and four washers must be mounted <br /> to the chassis. <br /> 4. Ensure liner dispenser is free from damage. Remove key, unlock, and open liner <br /> dispenser lid. This will expose liner dispenser mounting holes. Line up dispenser mounting holes <br /> onto chassis and secure with the four screws provided. Close and lock the liner dispenser door. <br /> 5. Clean work area and inspect unit to ensure it opens and closes smoothly. Give Operator <br /> Kit and key to the facility operator. Replacement parts and additional liners can be purchased from <br /> your local distributor or by calling Koala at 888.733.3456 or 303.539.8300. <br /> The illustrations and descriptions herein are applicable to production as of the date of this Technical Data Sheet. The <br /> manufacturer reserves the right to, and does from time to time,make changes and improvements in designs and <br /> dimensions without notice. <br /> refak <br /> Celebrat rAV:` <br /> Koala Kare Products 1 6982 S Quentin St. I Centennial,CO 80112 Koala Toll Free:888.733.3456 1 303.539.8300 I Fax:303.539.8399 <br /> www.koalabear.com <br /> P/N ABOO5 April 2012 <br />