2016-283-E Emergency Svc - FESCO Emergency Sales for the purchase of new ambulance

Browse Search

DocuSign Envelope ID: F4D38498-6182-495F-9F57-49F44D76229A AM10-14 Ambulances,EMS&Other Special Service Vehicles 3.7.6.1 Engine High-Idle Sneed Control. Automatic. On type I&III chassis powered emergency medical service units an automatic throttle providing variable RPM conditions shall be installed on the chassis in compliance with KKK specifications. When activated, the throttle shall automatically increase the engine RPM when the amperage goes into a deficit state and automatically decrease when positive amperage is achieved. 3.7.6.3 Voltmeter or Voltage Monitor. Voltmeter shall be mounted in the Operator Control Panel,if not provided by OEM. 3.7.8.1 Utilitv Power Connector. In cases where a 115 Volt AC utility power connector is installed on an emergency medical service unit, the outlet shall be located at an exterior location approved by the end user agency and unit manufacturer. If an inverter is installed the outlet shall be powered by the inverter unless the type I & III "high performance"emergency medical service unit is attached to shoreline electrical power,then the outlet shall be powered by the shoreline power. The outlet shall include a metal or heavy-duty plastic cover designed for outdoor use and be enclosed in an electrical outlet box. 3.7.8.3 Solid State Inverter for on Board 115 Volt AC Power. In cases where a 1000 watt, 115 Volts AC continuous duty inverter is installed and wired to interior and exterior outlets of an emergency medical unit, the inverter switch shall be loaded in the EMT action area unless otherwise specified by the end user agency. 3.7.9 Driver Compartment Controls. In cases where sequential switching systems are installed allowing the driver to preset at least six (6) emergency lights or other warning devices (a single switch automatically sequences and turns them on, one at a time), switches shall be large enough to be activated/manipulated by operator wearing thick gloves. 3.8.1 Ambulance Exterior Lighting. All units quoted shall include at least one (1) side floodlight on all emergency medical service units. 3.8.5.1 Patient Compartment Illumination. At least six(6) dome lights shall be furnished with at least three (3) over the stretcher and three(3)over the Squad Bench 3.9.7.3 Mud Flaps. Mud flaps on all emergency medical service units shall be furnished in compliance with State of Texas Motor Vehicle laws. 3.10.8 Doors. On type I & III emergency medical service units, door hardware shall consist of recessed, stainless steel, locking paddle latches on compartments. All door lock mechanisms shall be fully enclosed within the door to prevent fouling of locks in the event of equipment shifts in the lock area. Patient module doors shall use a recessed, polished stainless steel, handle and latches. All patient module locking latches shall use a common key, except the drug compartment. On type I&III emergency medical service units the door gaskets shall be placed in a manner that prevents damage by equipment or personnel dragging across the gaskets. All doors shall incorporate an extruded rubber seal located on the perimeter of the door. Full length stainless steel hinges, and pins shall be provided for all exterior doors. Over door padding shall be provided at the rear and curb side door,and above the walk-thru,if applicable. 3.10.11 Floor Coverings and Color. On all emergency medical service units (excluding Type II), the covering shall extend a minimum of four(4)inches up both side walls for easy cleaning. 3.11.1 Interior Stowage Accommodations. On Type I & III emergency medical service units the doors track for all sliding cabinet doors shall be constructed of extruded aluminum with slots for the installation of felt door tensioners on each side and a Teflon sliding guide on the bottom of the track. The material shall be installed in a slide or other manner providing ease of maintenance. The track shall be attached to the cabinet with recessed screws. Cabinetry on all emergency medical service units shall be included in patient module warranty and all exposed areas with an extruded aluminum edge shall be smooth. 3.11.4 Squad Bench. Seats. And Backrests. Seat belts furnished for the squad bench shall be automatic self- retracting on type I,II,&III emergency medical service units. 3.12.1 Oxvun.Main Sunnly and Installation. On type I&III emergency medical service units no less than three (3)outlets shall be provided;two(2)in the EMT action area and one(1)outlet on the curb-side wall. Storage dimensions and mounting device shall be provided for an"H"size cylinder,rather than an"M"size cylinder unless specified by the end user. 3.15.3.14 Drug Kit Compartment. On type I, II, & III emergency medical service units a locking drug compartment shall be furnished in compliance to KKK specifications. The locking drug compartment shall have a unique lock,keyed differently from all others on the unit and at least two keys shall be furnished. May 9,2014 -----FINAL----- Page 6 of 9