Orange County NC Website
Section 5.5 or <br />Somewhere in the Standards for Residential Uses or Development Standards there should be a section that specifies <br />section 6 <br />minimum residential driveway sizes of 12 feet wide by 14 feet vertical clearance (already stated in 7.8.5 (B) (15) on page <br />7 -32 for fire apparatus. This is the cleared width of the driveway, not the width of gravel or paving. <br />3 <br />Page 7 -25 <br />The travel -way width for Class B with 2 lots should be specified as 12 feet of cleared space, no standard for width of <br />ravel or hard surface. <br />3 <br />Page 7 -28 <br />Under (5) (b): 16 feet should be 18 feet so that a passenger car can be passed by fire apparatus. For Class B roads <br />with 3 or more lots, there should be an area 20 feet wide by 50 feet long every 1500 feed to that fire apparatus can pass <br />each other. <br />Page 6 -105 <br />6.12.11 (A) (6) should be "Signs for Non - profit or Not for profit organizations. Under the tax codes, I think these are two <br />separate designations and both should be allowed to have a sign. <br />Page 6 -106, (c) <br />Back in section 6.12.6 (a) (1) Portable signs are prohibited. On page 6 -106, special event signs are allowed. Can <br />portable signs be used here? I am thinking of things like a Fire Department fund raising event that would be displayed on <br />a portable sign that sits on the ground at the fire station. <br />1 <br />Page 6 -103 (K) <br />A restriction on single poll or mast signs seems overly restrictive. <br />Also in the section, can we make signs stapled to utility poles prohibited? I think they are by state law, but putting that in <br />these ordinances would give the county the ability to take action or just remove the sign). <br />1 <br />.11.3 page 6 -91 <br />On (1), remove the word "incandescent" since LED lights are now often used for holiday decorations. Low wattage is not <br />defined, but a typical nightlight(big Christmas tree bulb is 7 watts so you could say any wattage under 10 watts. It would <br />make more sense to use a lumen rating, such as less than 150 lumens. <br />On (J), first off this should be a lumen limit, not watts. As the limit reads, this looks like a total lumens for any given <br />motion activated switch. The lumens looks like it was derived from two incandescent 75 watt bulbs, probably flood <br />lights. Note that if this is the case, the maxim lumens should be 2400. There are many motion activated systems where <br />a sensor can turn on multiple light fixtures. so I would re -word this to have a 2400 lurnen limit per light fixture controlled <br />by the sensor. <br />Finally, on this max lumens per fixture, there are standard outdoor floodlight fixtures that take 3 bulbs. For those fixtures, <br />a reasonable max lumens would be around 3600. You could also add a limit of no one bulb can exceed a rating of 2100 <br />lumens a 120 watt equivalent) if the intent is to avoid the larger single bulb fixtures. <br />3 <br />6.11.4 page 6 -92 <br />(A) This is where a definition of "mercury vapor luminaries" is needed. As written, this could mean that any standard <br />fluorescent or compact fluorescent light could not be used, since they are a mercury-phosphorous based light. <br />3 <br />6.11.6 page 6 -95 <br />(C) (1) Some floodlight fixtures do not cover the bulb, the stop just after the threaded base. I'd just stick with the 45 <br />degree from vertical. <br />(c) (2) the "it will shine" is vague. Perhaps something like "no more than 5% of the luminous energy shall shine towards <br />roadways, onto adjacent residential property or into the night sky ". <br />(C) (3) Same vagueness- what is the "main beam "? Do you really want to say that no portion of the bulb shall be visible <br />from adjacent properties or the public street right -of -way? From an enforcement point of view, a "Can't see the bulb" is <br />easy to verify for both the owner and the inspector. Note that this is the approach taken on page 6 -97, 6.117 (3). <br />3 <br />6.11.6 page 6 -96 <br />(K) Back on page 6 -91, the time limit for motion controlled lights was 12 minutes, here it is 15. It would be cleaner if <br />there was one maximum timeout time for all motion controlled lights. <br />N <br />1) Incorporated; 2) For further BOCC discussion; 3) Implementation Bridge — Possible future phases; 4) Suggesting no action <br />